Joint Campus Placement Drive with M/s Emson Group of Companies for B-Tech / Diploma in Mechanical Engineering on 31/03/2018 at 10 AM Sharp for free Reg Contact TPO at 9805092578 / 9816608936  

ECE - About the Labs



Analog Circuits Lab

It is an introductory experimental laboratory that explores the design, construction, and debugging of analog electronic circuits. This subject covers diodes, transistors, JFETs, op-amps, and basic analog circuit design as applied to audio and radio frequency circuits. Students spend the second half of the term designing their own projects. Projects vary in scope and breadth, depending on students' level of prior background and interest. In the process, students will learn to understand and use a wide variety of analog circuits. They will learn how to use books and periodicals to find circuit ideas and to supplement their textbook knowledge. The laboratory satisfies the institute laboratory requirement. However, students often find it valuable to have taken more advanced circuit design classes, as they allow for more ambitious final projects.


Basic Electronics Lab

Electronics is the laboratory which puts knowledge of electricity to useful work.  Electronics applies electrical current flow of electrical charges to circuits to accomplish specific tasks.  Basic electronics is all about electrical components and the circuits consisting of those components.  Common components are resistors, capacitors, inductors, transistors, and integrated circuits. The components are interconnecting with conductors, either physical wires or printed circuits.  The components make up linear analog amplifiers, oscillators, and filters as examples. So students will find basic electronics in every computer, mp3 player, radio, TV and may other appliances in your home, car, or on your body. Components are interconnected to perform a specific task.

The laboratory satisfies the institute laboratory requirement. First learn about each individual component and how it works then learn about how to interconnect them to make useful end products. Continue your study by reading the books.


Communication System

A system is capable of providing information exchange between persons and equipment. The system usually consists of a collection of individual communication networks, transmission systems, relay stations, tributary stations, and terminal equipment capable of interconnection and interoperation so as to form an integrated whole. These individual components must serve a common purpose, be technically compatible, employ common procedures, respond to some form of control, and generally operate in unison.



Digital Electronics Lab

Digital electronics is based on electronic switches.  A circuit is either on or off represented by the presence of a voltage or not or in some cases two different voltages.  A string of on or off conditions are made to represent numbers.  These are usually binary numbers but could be based on a variety of mathematical bases. .  Any number can be represented in a binary based system with a series of ones' and zero's. These basic concepts are the building blocks for more sophisticated configurations of digital electronic integrated circuits.  Today digital integrated circuits combine hundreds and thousands of switches per IC package.  It is not necessary to know exactly what the internal circuitry is but you must know the fundamentals to understand how to use the IC's together to build digital equipment. 

Our computer industry today depends upon many people knowing and using these same basic fundamentals. The laboratory satisfies the institute laboratory requirement.


Electronic Circuit Simulation

Electronic circuit simulation uses mathematical models to replicate the behavior of an actual electronic device or circuit. Simulating a circuit’s behaviour before actually building it greatly improves efficiency and provides insights into the behaviour of electronics circuit designs. In particular, for integrated circuits, the tooling (photomasks) is expensive, breadboards are impractical, and probing the behaviour of internal signals is extremely difficult. Therefore almost all IC design relies heavily on simulation.

The most well known analog simulator is SPICE. Probably the best known digital simulators are those based on Verilog and VHDL. Printed circuit board (PCB) design requires specific models as well, such as transmission lines for the traces and IBIS models for driving and receiving electronics.


Electrical Measurements and Instrumentation Lab

Measurement is the process or the result of determining the magnitude of a quantity, such as length or mass, relative to a unit of measurement, such as a meter or a kilogram.EMI lab comprises of measuring instruments and devices for performing various experiments related to measurement of important electrical parameters like voltage, current, power, energy, frequency, inductance and capacitance etc.

The laboratory satisfies the institute laboratory requirement.




Matlab is a computing environment specially designed for matrix computations. It is widely used for the study of a variety of applications, including circuits, signal processing, control systems, communications, image processing, symbolic mathematics, statistics, neural networks, wavelets, and system identification. Its large library of built-in functions and toolboxes, as well as its graphical capabilities, make it a valuable tool for electrical engineering education and research. Matlab has an interactive mode in which user commands are interpreted immediately as they are typed. Alternatively, a program (called a script) can be written in advance using a text editor, saved as a file, and then executed in Matlab. 

The objective of this lab is to review how to access Matlab, Simulink, and the Communications Toolbox, and to become familiar with the basic operations of these applications.

Contact us

Call : 098160-79160, 094180-00903,94180-77444 / Email:,


Admission Enquiry

JEE Exam Appear Yes/No: Yes No

News & Announcements



Meritorious Students of SIET

  • Shilpa Mahajan (M.Tech) 1st in HPTU

  • Rubi Chandel (EEE) Topper SIET 2016

  • Pooja Sharma (CSE) Topper SIET 2016

  • Pankaj Barwal (CE) 3rd in HPTU 2016

  • Gaurav Sharma (ME) 2nd in HPTU 2016

  • Mr. Vishal Mahajan(civil 1st sem) Rank 7th HPTU

  • Mr. Mahender Singh(ME 1ST Sem) Rank 2nd in HPTU

  • Mr. Ajay Kumar (CSE 1st Sem) Rank 3rd in HPTU

  • Miss Shalini CE 1st sem Rank 2nd in HPTU

  • Miss Neelam Kumari ECE (1st Sem) HPTU Topper

  • Vishal Mahajan (ME) Rank 1st HPU

View all Meritorious Students


Our Recruiters

See all recruiters / companies >

Photo Gallery

Visit our Photo Gallery section


Copyright 2014, SIET, Bilaspur, H.P, All rights reserved. | Project Maintained by Parvinder Chandel and Mr. Shashi Thakurl
Website design, development & hosting at : | Visitors :
since 5th April 2011